barnfinder
Training Wheels
Ride On Ride Hard
Posts: 166
|
Post by barnfinder on Aug 18, 2011 22:21:21 GMT -4
1974 CB360, only running on one cylinder. Found out that an adjustment screw on points plate was stripped. Warmed it up found it has good compression and now the tear down begins. Attachments:
|
|
barnfinder
Training Wheels
Ride On Ride Hard
Posts: 166
|
Post by barnfinder on Aug 18, 2011 22:23:48 GMT -4
Down to frame, and goodies. Know to make a list of parts, modifications. Attachments:
|
|
barnfinder
Training Wheels
Ride On Ride Hard
Posts: 166
|
Post by barnfinder on Aug 18, 2011 22:25:33 GMT -4
Engine will be getting all new seals and gaskets. Not to fond of just getting it going and tearing it down again. Attachments:
|
|
|
|
Post by leadkrm on Aug 18, 2011 23:04:34 GMT -4
Sweet what color are u doing the frame
|
|
|
|
Post by cb500bobber on Aug 19, 2011 0:24:42 GMT -4
I had to run out to my garage and make sure mine was still there thats exactly what mine looks like lol.
|
|
barnfinder
Training Wheels
Ride On Ride Hard
Posts: 166
|
Post by barnfinder on Aug 25, 2011 10:44:03 GMT -4
Well the mock up begins, so I can get a visual of what I want it too look like. Not too sure what color I will do the frame, but I'm leaning towards gloss black. Attachments:
|
|
|
|
Post by tango911 on Aug 25, 2011 16:05:31 GMT -4
looking good, whats your eta to finish?
|
|
barnfinder
Training Wheels
Ride On Ride Hard
Posts: 166
|
Post by barnfinder on Aug 25, 2011 16:14:46 GMT -4
I'm looking to get it finished in a couple months. Its going to be a rider. I have most of my parts to put it back together. Will fiberglass a seat cowl for it and one of my transitions from my work on airplanes will be a tail beacon light for a running light/brake light.
Went to Cycle-Recycle II today to get a carb slider due to the fact mine has wear holes in them. I think I got stuck with cb350 one due too its just a bit smaller than mine.
|
|
barnfinder
Training Wheels
Ride On Ride Hard
Posts: 166
|
Post by barnfinder on Aug 27, 2011 18:52:23 GMT -4
Progress being made. Now to make noise and clean the frame up. Attachments:
|
|
barnfinder
Training Wheels
Ride On Ride Hard
Posts: 166
|
Post by barnfinder on Aug 27, 2011 18:54:01 GMT -4
Mock up continues... Attachments:
|
|
|
|
Post by 72cl350 on Aug 28, 2011 22:52:33 GMT -4
Looks sweet. Wish I had that tank
|
|
barnfinder
Training Wheels
Ride On Ride Hard
Posts: 166
|
Post by barnfinder on Sept 7, 2011 21:03:08 GMT -4
RH controls and tach installed. Attachments:
|
|
barnfinder
Training Wheels
Ride On Ride Hard
Posts: 166
|
Post by barnfinder on Sept 7, 2011 21:05:35 GMT -4
Brake/tail light mounted. Progress has been slower than anticipated due to severe allergies during this time of year. But will continue. Attachments:
|
|
barnfinder
Training Wheels
Ride On Ride Hard
Posts: 166
|
Post by barnfinder on Sept 8, 2011 21:23:02 GMT -4
Front end is done! Attachments:
|
|
barnfinder
Training Wheels
Ride On Ride Hard
Posts: 166
|
Post by barnfinder on Sept 8, 2011 21:27:10 GMT -4
Wiring is ran thru the clubmans for cleaner look. Cables ran for routing. Turn signal, high beam and neutral indicators mounted. Will be forming the tail section, seat out of high density foam and then do a sandwich composite layup. Then it will be taken all apart for finishing and paint. While the motor gets tore down for new gaskets and seals. Attachments:
|
|
